type i emulsified asphalt slurry seal 

type i emulsified asphalt slurry seal

  • TYPE I EMULSIFIED ASPHALT SLURRY SEAL SURFACE …

    TYPE I EMULSIFIED ASPHALT SLURRY SEAL SURFACE TREATMENT DESCRIPTION 1.1 These are the requirements for furnishing materials and applying (by slurry laydown machine) Type I asphalt emulsion slurry seal on the dense graded asphalt surfaces of Runway 3/21 and the Taxiway/Apron as shown in Figure 2 attached hereto.

    Get Price

  • Slurry Seal Treatment Types

    A slurry seal is the application of a mixture of water, asphalt emulsion, aggregate (very small crushed rock), and additives to an existing asphalt pavement surface. A slurry seal is similar to a fog seal except the slurry seal has aggregates as part of the mixture. This combined mixture of the emulsion and aggregates represents “slurry.”

    Microsurfacing · Chip Seals

    Get Price

  • Slurry Seals - Pavement Interactive

    A slurry seal is a homogenous mixture of emulsified asphalt, water, well-graded fine aggregate and mineral filler that has a creamy fluid-like appearance when applied. Slurry seals are used to fill existing pavement surface defects as either a preparatory treatment for other maintenance treatments or as a wearing course. There are three basic ...

    Get Price

  • SLURRY SEAL SPECIFICATIONS – (1%, 3% ... - co …

    emulsion shall be pumpable and suitable for use in a Slurry Seal machine. The emulsified asphalt shall conform to the requirements of the ASTM specification for quick set CQS with revisions as indicated in the table below. In addition, the emulsion shall contain 1%, 3% minimum SBR latex solids based on weight of asphalt cement. The slurry seal ...

    Get Price

  • Slurry Seal California Pavement Maintenance (CPM)

    What is Slurry Seal? Slurry seal is a mixture of emulsified asphalt, crushed aggregate, water, and set-control additives such as aluminum sulfate and/or Portland cement. Slurry may also use a variety of polymers to enhance the toughness and tenacity of the finished mix.

    Get Price

  • Section 427 Emulsified Asphalt Slurry Seal

    Emulsified asphalt slurry seal is used to seal small cracks and correct moderate surface condition. Apply this type at a rate of 10 to 20 lbs/yd² (5.5 to 11 kg/m²) based on dry aggregate weight. If more than 20 lbs/yd² (11 kg/m²) of emulsified asphalt slurry seal is required, apply additional lifts of the same mixture.

    Get Price

  • For Emulsified Asphalt Slurry Seal

    FOR EMULSIFIED ASPHALT SLURRY SEAL 1. SCOPE The intent of this guideline is to aid in the design, testing, quality control, measurement and payment procedures for the application of Emulsified Asphalt Slurry Seal Surfacing. 2. DESCRIPTION Slurry seal shall consist of a mixture of an emulsified asphalt, mineral aggregate, water, and additives,

    Get Price

  • Slurry Surfacing - International Slurry Surfacing Association

    TITLE Slurry Seal Consistency Template View store here to download. The principal materials used to create slurry seal are aggregate, asphalt emulsion, and filler, which are mixed together according to a laboratory’s design-mix formula. Water is also added for workability.

    Get Price

  • Slurry Seal Vs Seal Coat - Asphalt Paving and Repair ...

    Slurry Seal Vs Seal Coat. Slurry seal vs seal coat—which of these sealing options is right for your road paving, asphalt driveways, parking lots or playgrounds?While the terms are often used interchangeably because both protect and extend the life of your asphalt surfaces, the two applications are different.

    Get Price

  • Slurry Seal Preparation - American Asphalt

    Slurry seal is an asphalt slurry mixture made from closely graded fine aggregate, emulsified asphalt and water, all carefully calibrated and mixed to form a mortar-like compound.This mixture is designed for easy and efficient spreading as a sealer on streets, playgrounds, parking lots and driveways.

    Get Price

  • Slurry Seals McAsphalt

    Slurry seal is a mixture of aggregate, emulsified asphalt, water and additives that are properly proportioned, mixed and spread over a prepared surface. A polymer-modified system can be used in the same application and will enhance one or more properties of the …

    Get Price

  • Applications for asphalt emulsions Asphalt magazine

    Applications for asphalt emulsions. Asphalt emulsions can be used for almost any type of pavement application. They can be used for preventive and corrective maintenance on both asphalt and concrete pavements, stabilizing and reclaiming bases, building structural pavements and recycling worn out pavements. ... A slurry seal is designed to seal ...

    Get Price

  • Slurry Seal Emulsion - graniterock

    Emulsified asphalt used in the slurry mix may be SS-1, SS-1h, CSS-1, or CSS-1h. The recently developed quick-setting (CQS) asphalt emulsion is being used when early opening to traffic is necessary. Blending the slurry seal materials in varying proportions in …

    Get Price

  • The Difference Between Slurry Seals and Sealcoating G P ...

    You may not realize it, but when it comes to asphalt maintenance, there is a difference between "slurry" and "sealcoating."While both slurry and sealcoating are preventative maintenance tasks that extend the life of your asphalt, there are key differences that you should be aware of.

    Get Price

  • Standard Practices for Design, Testing, and Construction ...

    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.. Other Documents. ISSA A105 Recommended Performance Guidelines For Emulsified Asphalt Slurry Seal. ISSA Technical Bulletin No. 139 ASTM Standards. C128 Test Method for Relative Density (Specific Gravity) and Absorption of …

    Get Price

  • Recommended Performance Guidelines

    RECOMMENDED PERFORMANCE GUIDELINES FOR EMULSIFIED ASPHALT SLURRY SEAL 1. SCOPE The intent of this guideline is to aid in the design, testing methods, quality control, measurement and payment procedures for the application of Emulsified Asphalt Slurry Seal …

    Get Price

  • CONSTRUCTION SPECIFICATION FOR SLURRY SEAL

    A summary of the quantity and application rate of slurry seal placed and a list of the quantities used for each of the slurry seal components (i.e., aggregate, emulsified asphalt, mineral filler, and additive) shall be submitted daily to the Contract Administrator.

    Get Price

  • Section 7070 - Emulsified Asphalt Slurry Seal

    Emulsified Asphalt Slurry Seal 1.02 DESCRIPTION OF WORK Includes the requirements for surface treatment of an existing pavement with an application of an emulsified asphalt slurry seal. In addition, the work may involve the following items A. Slurry Leveling Use fine slurry mixtures to fill shallow depressions in the pavement and over cracks.

    Get Price

  • SLURRY SEAL SURFACING. (REV 9-15-14) SECTION 335 …

    SLURRY SEAL SURFACING 335-1 Description. Construct a slurry seal with the type of mixture specified in the Plans. Slurry seal is a mixture of polymer-modified emulsified asphalt, mineral aggregate, mineral filler, water, and other additives, properly proportioned, mixed and spread on a paved surface. The mix shall be capable

    Get Price

  • SPECIAL SPECIFICATION 3250 Emulsified Asphalt Slurry …

    The design of the emulsified asphalt slurry seal should be a creamy-textured slurry that, when spread, will flow ahead of the strike-off squeegee and will flow down into the cracks in the pavement and fill them. Technical Bulletin No. 111, “Outline Guide Design Procedure for Slurry Seal”, and publication A-105,

    Get Price

  • SECTION 5 SELECTING THE RIGHT TYPE AND GRADE

    The first consideration in picki ng the right type and grade of emulsion is how the emul-sion will be used. Is it for a seal coat, a plant mix (cent ral or mixed-in-p lace), a recycled mix or a prime coat application? Is it for some type of surface application, such as a chip seal, fog seal, slurry seal or …

    Get Price

  • Slurry Seal Missouri Petroleum

    A Slurry Seal is a cold, mixed asphalt slurry. It consists of emulsified asphalt, graded fine aggregate and additives. It is a hard wearing surfacing for pavement preservation.

    Get Price

  • SECTION 02505 EMULSIFIED ASPHALT SLURRY SEAL

    A. The slurry seal shall consist of a mixture of an approved emulsified asphalt, mineral aggregate, water and specified additives, proportioned, mixed and uniformly spread over a properly prepared surface. The completed slurry seal shall leave a homogeneous mat, adhere firmly to the prepared

    Get Price

  • Slurry Seal - Southwest Slurry Seal, Inc.

    COMMERCIAL SLURRY SEAL IN ARIZONA COMMERCIAL SLURRY SEAL Quick-set Slurry is emulsified asphalt, crushed rock and cement mixed and applied with specialized equipment forming a thick, tough, durable mixture that Fills cracks Seals against damaging moisture invasion Completely hides utility trench patches and other repair work Resurfaces your asphalt with a 1/4 to 1/2″ […]

    Get Price

  • VIRGINIA DEPARTMENT OF TRANSPORTATION SPECIAL …

    86 S312DM2-1112 VIRGINIA DEPARTMENT OF TRANSPORTATION SPECIAL PROVISION FOR EMULSIFIED ASPHALT SLURRY SEAL September 28, 2012 I. DESCRIPTION This work shall consist of furnishing and applying an emulsified asphalt slurry seal as specified

    Get Price

  • slurry seal surface specifications - lcrconline

    SLURRY SEAL SURFACE SPECIFICATIONS DESCRIPTION The Slurry Seal Surface shall consist of a mixture of emulsified asphalt, mineral aggregate and water, properly proportioned, mixed and spread evenly on the surface as specified herein and as directed by the Engineer. The cured slurry shall have a homogenous appearance and a skid resistant texture ...

    Get Price

  • Slurry Pavers Inc - About Us

    Slurry Pavers, Inc. was founded in 1966 as one of the original Pavement Preservation companies in the United States. From the beginning to the present day, SPI has played a significant role in product, staff, equipment and process development for the Pavement Preservation industry.

    Get Price

  • An Introduction to Asphalt Emulsions Asphalt magazine

    An Introduction to Asphalt Emulsions. ... An asphalt emulsion is liquid asphalt cement emulsified in water. It is composed of asphalt, water and an emulsifying agent. The emulsifying agent is sometimes called the surfactant, which is composed of large molecules. ... QS emulsions are used in micro-resurfacing and slurry seal designs. The quick ...

    Get Price

  • Pavement Treatment - Slurry Seal - Info Virginia ...

    Aug 17, 2016 · Slurry Seal. Slurry seal is a mix of asphalt emulsion and aggregate that is spread over the entire roadway surface. It is applied by a truck equipped with a squeegee or spreader box. Slurry seals address longitudinal cracking, transverse cracking, weathering, the loss of friction, moisture infiltration, and roughness.

    Get Price

  • Slurry Seal Surfacing Hardrives Construction

    Slurry Seal Durability and Economy make Slurry Seals a Great Option in Asphalt Maintenance. Slurry seals provide a new wear surface over structurally sound asphalt and reduce the need for costly repairs. Properly applied, a slurry seal has a typical life expectancy of 5-8 years. The advantages of a slurry seal are twofold.

    Get Price

  • Preventive Maintenance - Slurry Seal

    General. The slurry seal shall be capable of field regulation of the setting time. The compatibility of all ingredients of the mix, including the mix set additive, shall be certified by the emulsified asphalt manufacturer. Weather Limitations. Placement of the slurry seal shall be done between May 1 and

    Get Price

  • Slurry Seal Ergon Asphalt & Emulsions, Inc.

    A preventive or corrective maintenance surface treatment composed of a mixture of dense-graded aggregate, emulsified asphalt, mineral fillers, additives and water. The slurry seal improves surface texture, and seals and protects the pavement. Emulsion is mixed with aggregate and then placed on road. Can fill some cracks.

    Get Price

  • Tack Coat to Chip Seal - Louisiana Transportation …

    Tack Coat to Chip Seal Danny Gierhart, P.E. Regional Engineer Asphalt Institute . ... emulsifier type and water pH . ... •Slurry Seal •Micro surfacing •Cape Seal •Fog Seal •Scrub Seal •Penetration Macadam Surface Treatments .

    Get Price

  • International Slurry Surfacing Association

    2020 Slurry Systems Workshop. 2/17/2020 » 2/21/2020 2020 AEMA-ARRA-ISSA ANNUAL MEETING. ... Highway 30 Cape Seal. This 14 mile project on Highway 30 in the Hiawasee Ocoee State Park in Polk County Tennessee was completed by Strawser Construction for the Tennessee Department of …

    Get Price

  • ITEM 417 ASPHALT EMULSION SLURRY SEAL - City of …

    ITEM 417 ASPHALT EMULSION SLURRY SEAL 417.01 Description 417.02 Materials ... A. Asphalt Emulsion. Furnish emulsified asphalt conforming to AASHTO specifications for dense mixing grade SS-1h except that they shall be of the QUICK SET SLURRY SEAL EMULSION TYPE, either anionic or cationic, whichever in the ...

    Get Price

  • Recommended Performance Guidelines

    Polymer-modified emulsified asphalt slurry seal shall consist of a mixture of -modifieda polymer emulsified asphalt, mineral aggregate, water, and additives, proportioned, mixed and uniformly spread over a properly prepared surface as directed by the Buyer's Authorized Representative (B.A.R.).

    Get Price

  • Asphalt Seal-Coat Treatments - US Forest Service

    Any of the asphalt seal coat treatments could improve a pavement with raveling problems. For low-severity raveling, a fog seal could treat the problem while a chip seal or slurry seal would be needed for medium to high severity raveling. A rejuvenating treatment may also restore the binding properties of an aged pavement surface.

    Get Price

  • Airport Construction Standards (AC 150/5370-10) – Airports

    Provides individual specifications from AC 150/5370-10, Standards for Specifying Construction of Airports, including construction standards for general provisions, earthwork, flexible base courses, rigid base courses, flexible surface courses, rigid pavement, fencing, drainage, turfing, lighting installation, pavement rejuvenation

    Get Price

  • Micro-Surfacing Emery Asphalt

    Micro’s effectively seal, level, rejuvenate, and aid in skid resistance on existing paved surfaces. Micro-Surfacing can be applied in a wide range of thicknesses, allowing it to treat a large variety of road surfaces. It is a cold mix type paving system leaving minimal impact on the environment.

    Get Price

  • 302-4 EMULSION-AGGREGATE SLURRY. 302-4.1 …

    302-4 EMULSION-AGGREGATE SLURRY. 302-4.1 MATERIALS. ... emulsion, additive and asphalt modifier to the mixer and of discharging the thoroughly mixed slurry on a continuous basis. Each mixer shall have a metering device to measure the quantity of water in gallons used in ... Slurry Seal Min. Max. Min. Max. Type I 8 lbs./yd² 11 lbs./yd² ELT ...

    Get Price

  • VSS International - Seal Coat - Prevent Pavement Oxidation

    Binders are selected for the type of job. Binders may be emulsified asphalt or coal tar, emulsified polymer asphalt, latex modified emulsified asphalt, rejuvenating oil modified asphalt emulsions or hot applied binders with asphalt rubber fibres or polymers. VSS will advise on the type of seal …

    Get Price

  • emulsified asphalt

    The design and instrumentation of a solar heating system to maintain adequate temperatures in emulsified asphalt storage tanks Final report (2/18/80-6/30/81) by D. N Koppenhaver Unknown Binding

    Get Price

Contact
+86-21-61902951 [email protected] 0086-21-61902951 24 Hours Online! Chat Us Freely!